Instructions for use

Neutrarust 661® – is a water based non-hazardous rust converter that is simply painted.

Stir well before use. Do not dilute.

Remove flaky rust, loose scale and dirt with thorough wire brushing. Reduce any high peaks of rust. Paintwork blistered by rust should be scraped down to hard rust surface. IMPORTANT – DO NOT REMOVE ALL TRACES OF HARD RUST. Remove acid, alkali, grease oil and chemicals with detergent water wash then rinse surface with clean cold water. These areas must be adequately covered with Neutrarust 661®

Before use. pour into non metallic container to avoid the transfer of rust particles into original container. Do not pour unused portion back into original container.

Apply 2 or 3 thin coats of Neutrarust 661® by brush, spray or roller. Cross brush for best results. Spray application should be made by applying a light mist coat. Once cured dry apply next coat.  Rust will turn to a dark ready-to-paint surface. It can dry to a high gloss finish. Being water-based, Neutrarust 661® adsorbs any surface moisture during its curing process and the strong resin forms a seal.

During application of Neutrarust 661® it changes colour from off white to blue to a ready to paint surface. At the blue stage continue gently brushing for a further minute and allow to dry for the chemical reaction. Leave 24-48 hours to dry hard depending on weather conditions before applying primer or topcoats of paint. Surplus Neutrarust 661® may cause staining of surrounding paintwork if allowed to dry. Remove surplus immediately.

Neutrarust 661® is self priming and is an excellent base for a wide range of paints. It is preferable, but not essential to use a good quality primer before applying topcoats. Test compatibility before use.

TEMPERATURE RANGE, USE & STORAGE

Neutrarust 661® should not be applied to cold metal below 5°C or hot metal above 40°C. But will withstand temperatures between -40°C and 60°C when dried hard. Store between  5°C and 35°C. Not to be used or stored outside of recommended temperatures.  Replace cap after use. Use in adequately ventilated area. Do not store in direct sunlight.

P280: wear protective gloves & eye protection

DRYING TIMES – Each Coat Touch dry—summer approx. 20 minutes, winter approx. 45 minutes. Between coats: summer and winter approx. 2 hours. Protect from rain during drying

CLEANING BRUSHES OR SPILLAGE Use detergent water wash and rinse with water or industrial solvents.

Neutrarust 661® MUST NOT BE SWALLOWED If swallowed, wash out mouth with water and give water to drink. Harmful by inhalation treat symptomatically. Eyes: splashes to the eye should be removed by washing with eyewash solution or water for at least 10 minutes. Skin: splashes should be washed off with water and soap as soon as possible. If in any doubt as to effectiveness of any treatment, obtain medical attention immediately.

KEEP OUT OF REACH OF CHILDREN. SLIGHT IRRITANT

Classified non-hazardous, non-combustible & dry film is fire retardant

CONDITIONS OF SALE – Since we have no control over the working conditions, different materials involved and the circumstances under which the purchaser stores, handles or uses this material, we make no warranty or condition, either express or implied, with respect to this material.

EUH210: Safety data sheet available on request.

rust coloured floor

Steel Plate with Rust

rust coloured floor with blue paint

Freshly Applied

brown floor with silver paint

End result: protected and great appearance

Neutrarust 661® your hallmark of the original product. BEWARE of COPIES.
Neutrarust 661® Registered Trademark of and produced by Neutra Rust Europe Ltd.

Neutrarust 661

®​

Contact

Copyright © Neutrarust 661 | All Rights Reserved 2023

Neutra Rust Europe Limited, 4 Comet House, Calleva Park, Aldermaston, Berkshire, RG7 8JA

Telephone: +44 (0) 118 206 7788
Email: sales@neutrarust.co.uk

Neutrarust 661® Registered Trade Mark of Neutra Rust Europe Limited